Studio

Lost-Resin Casting

Lost-resin is a casting method in which a pattern printed in castable resin is invested in casting plaster and then burned out in a kiln. The resin disappears and leaves an empty cavity in the shape of the pattern, which the metal then fills. This is how we cast rings and figurines in silver and gold.

The name and how it differs from lost-wax

All variants of this technique rest on one principle: surround the pattern with investment, burn it out and cast metal in its place. The word lost refers to the pattern that is lost in the process. The difference is in the pattern material. In lost-wax it is carved or injected wax, in lost-PLA an FDM print with a layer of 0.1 to 0.3 mm, and in lost-resin an MSLA print in castable resin with a layer of 0.025 to 0.05 mm. That is why lost-resin reproduces filigree, openwork and fine relief so well.

How the process runs here

The whole process takes eight steps:

  • a CAD model scaled up in advance by the shrinkage of the chosen alloy
  • the pattern printed on the Elegoo Saturn 4 Ultra 16K, layer 0.05 mm or 0.03 mm
  • washing in isopropyl alcohol and drying
  • UV curing, and only then removing the supports
  • attaching the pattern to the main sprue, usually 2.0 to 2.5 mm in diameter
  • investing in Omni-II plaster in a flask, with at least 15 to 20 mm of plaster above the crown of the model
  • burning out the flask in a kiln, where the resin burns without harmful ash
  • vacuum casting, followed by breaking out the plaster, cutting off the sprues, grinding and polishing

Why vacuum casting

In gravity casting the metal runs into the cavity under its own weight. With the thin, openwork channels that lost-resin patterns leave, molten metal can solidify before it fills the finest detail. A vacuum draws the metal deep into the mold, so details of 0.2 to 0.3 mm fill correctly, and the casting has fewer pores and needs fewer corrections during finishing.

Which resins and which metals

We print patterns in BlueCast resins: X-Wax Filigree for delicate detail and X-One V2 for massive bodies. We cast silver and gold in the fineness offered in the casting service. When you send your own pattern, you state its material, and for a print in castable resin also the name and manufacturer of the resin, because we match the burnout profile to it. The pattern has to arrive washed and fully cured.

Common mistakes

These are the things to watch most:

  • a resin that does not burn out cleanly, leaving ash that ruins the mold
  • no shrinkage compensation, so the casting comes out smaller than the design
  • double compensation, when the file is already scaled up and the foundry scales it a second time
  • too thin a layer of plaster above the model, which collapses under vacuum
  • removing supports from an under-cured pattern, which bends delicate parts

What happens to the pattern

The pattern is destroyed, because it burns out of the mold. This is a single-use cast: another piece needs another pattern or a saved file. That is why the 3D file is the most valuable part here, not the print.

Frequently asked questions

Can any resin be used to cast jewelry?

No. You need a castable resin that burns out with almost no ash, such as BlueCast X-One V2 or X-Wax Filigree. Ordinary miniature resins leave ash and ruin the mold.

Does the pattern survive the casting?

No. The pattern burns out of the mold, so it is consumed. What remains is the 3D file, from which the next one can be printed.

Why must the model be scaled up before printing?

Metal shrinks as it solidifies, so the pattern is printed slightly larger than the finished piece. The factor depends on the alloy, and you can work it out in the shrinkage calculator.

Can I send my own pattern?

Yes, wax or a print in castable resin. The pattern has to arrive washed and fully cured, and for a resin print you state its name and manufacturer.

We can make it for you

Precious metal casting

Pattern, 3D model or idea. Silver and gold, our metal or yours.

from €180.43