MSLA Printing
MSLA printing is a resin technology in which a whole layer of the model cures at once under UV light shining through a mono LCD screen. At AEJaCA sTuDiO we print this way on an Elegoo Saturn 4 Ultra 16K: figurines, miniatures and casting patterns for jewelry.
How MSLA printing works
The LCD shows the cross-section of one layer, UV light cures the resin across that whole cross-section at the same moment, the build plate lifts by one layer height and the cycle repeats. There is no head tracing the outline point by point, as in classic laser SLA, and no nozzle extruding filament, as in FDM. Resolution in the plane is set by the size of the screen pixel, and vertically by the layer height.
Equipment and parameters at AEJaCA
We do our resin printing on one well-known machine. These are the parameters that matter for quality:
- a 16K screen of 16384 x 9216 px with a pixel of 14 x 19 µm
- layer height usually 0.05 mm, 0.03 mm for the finest details
- a heated vat (30°C) that keeps the resin viscosity stable whatever the room temperature
- Tilt Release, a gentler peel of the layer from the film, important for delicate, filigree shapes
- a build volume of 218 x 123 x 250 mm
MSLA versus FDM
Resin printing reproduces detail from about 0.2 mm and gives a smooth surface, while in FDM the limit is set by the nozzle diameter, usually 0.4 to 0.8 mm. That is why we choose MSLA where surface texture matters more than strength: miniatures, collectible figurines and jewelry patterns. A functional part that has to carry load or be large usually comes out better in FDM.
Post-processing
A print leaves the machine wet with uncured resin. We wash it in isopropyl alcohol (99.9% IPA) in two stages, rough and fine, dry it with compressed air and cure it in a UV chamber with a 360° turntable. Only after full curing do we remove the supports. Washing and post-curing are part of the service, so the model reaches the customer ready to use.
Resins for casting
An ordinary miniature resin leaves ash when it burns, and the ash ruins the investment mold. For casting patterns we therefore use only BlueCast castable resins, which burn out without harmful residue. X-Wax Filigree contains over 80% wax and is meant for filigree and detail from 0.2 mm. X-One V2 has zero shrinkage and suits massive parts such as shanks and crowns. A pattern in such a resin goes into the investment, and after burnout it leaves an empty cavity for the metal.
Common mistakes
Three mistakes come up again and again:
- removing supports before the UV cure is complete: after washing the resin is still soft and plastic, so thin parts bend or snap off
- using an ordinary resin for a casting pattern, which ends with ash in the mold
- expecting an MSLA print to have the strength of a functional part, because this technology is for surface texture, not for strength
Frequently asked questions
How does MSLA differ from classic SLA?
In classic SLA a laser traces the outline point by point. In MSLA a whole layer cures at once under UV light shining through a mono LCD screen, and the resolution comes from the size of the screen pixel.
Can any resin be used for casting patterns?
No. You need a castable resin, for example BlueCast X-One V2 or X-Wax Filigree, because ordinary resins leave ash and ruin the investment mold.
What level of detail can be reproduced?
The printer pixel is 14 x 19 µm, and the layer height for jewelry patterns is 0.05 mm or 0.03 mm. In practice we reproduce filigree and details from about 0.2 mm.
What does the resin printing service include?
Printing, washing in isopropyl alcohol and UV post-curing. The price is calculated from the geometry of the uploaded model, not from a range.
MSLA resin printing
14 µm micro-detail: figurines, miniatures, casting patterns.
from €26.69